【動画で紹介】 送信機と受信機のペアリングについて 45053 ファインスペック2.4Gプロポ

Pairing transmitter and receiver (Item 45053: Finespec 2.4GHz Radio Control System w/ESC)

2チャンネルプロポ「ファインスペック2.4G(ITEM 45053)」は、クリスタル交換やバンド管理の必要がなく複数台での走行が可能な2.4GHzホッピングシステムを採用。送信機と受信機のペアリングを再設定する方法について動画で紹介します。参考にしてください。

Please refer to the following instructions along with the videos when pairing transmitter and receiver.

【RCカーが動かない、操作できないときは!ペアリングを再設定してみましょう】 Pairing is required if the model doesn't move.

『ペアリングとは』 2.4GHzの電波でコントロールされるRCカーはBluetooth機器と同じように、送信機と受信機を無線操縦するためのペアリングが必要です。ペアリングすることで、他人が使っている送信機の電波に影響されることなく自分のRCカーをコントロールできます。工場出荷時には送・受信機はペアリングされていますが、ごくまれにペアリングが切れてしまうことがあります。

送信機、受信機のスイッチを入れてもRCカーが動かず、さらに受信機側のLEDが点灯していない場合は再ペアリングが必要です。

What is "Pairing"? The 2.4GHz radio control system requires pairing of transmitter and receiver for radio control of your model.Pairing enables control of R/C models without their being affected by other transmitters' signals.

Pairing is required if the model doesn't move despite the transmitter and receiver being on, and the receiver LED does not light up.

45053「ファインスペック2.4Gプロポセット」の送信機と受信機のペアリングを再設定する
Pairing transmitter and receiver (Item 45053: Finespec 2.4GHz Radio Control System w/ESC)

  • @ 送信機と受信機を1m以内に近づける。
        Position transmitter and receiver within 1m of each other.
  • A 受信機のリンクスイッチを押しながら、電源スイッチを入れる。
        Switch on the receiver while pressing its link switch.
  • ➂ 送信機のファンクションスイッチを押しながら、送信機の電源スイッチを入れる。
        Switch on the transmitter while pressing its function switch.
  • ➃ 送信機のLEDは「赤点滅」になる。
        Transmitter LED will flash Red.
  • ➄ 送信機と受信機のペアリングが成功。
        Pairing is completed.
  • ➅ 電源スイッチを入れ直します。
        Switch transmitter and receiver off and then on again.

モーターの設定(XBシリーズなどのブラシモーターモードの場合)
Motor Mode Setup for Brushed Motor Mode (XB models, etc.)

  • @ 送信機の電源スイッチをオンにする。
        Switch on transmitter.
  • A ESCのセットボタンを押したまま受信機の電源スイッチをオンにする。
        Switch on receiver while holding down Set button on ESC.
  • ➂ LEDが「赤」「緑」「橙(オレンジ)」に繰り返し点灯。
        LED lights up in the order Red → Green → Orange.
  • ➃ セットボタンを離します。
        Release Set button.
  • ➄ 「橙(オレンジ)」「緑」が交互に点灯。
        LED lights up Orange → Green → Orange.
  • ➅ セットボタンを押します。
        Press Set button.
  • F LEDが「緑」に点滅。
        LED flashes Green.
  • G もう一度「緑」が点灯。設定完了。
        Setup is complete when LED lights up Green.

2025年2月12日